Replacing the Keyboard - Remote

Replacing the Keyboard - Remote


Info
Your keyboard remote can be replaced if it no longer works or has been damaged beyond use. To order a new keyboard remote, please visit https://play-lu.odoo.com/.

After receiving the new remote, open the back panel to remove the USB receiver. This receiver needs to be plugged into the computer for the keyboard remote to work properly."

Note: The USB receiver may need to be replaced if the new remote is a different model than your previous one. The receiver’s location may vary depending on the Lü model you have. 


     

Lü 2nd generation

Using a ladder, lift, or scaffold, access the heart module located directly above the projection screen. The USB receiver is attached to the end of the USB cable hanging below the heart. Make sure this cable is positioned correctly to optimize signal reception from the keyboard remote. If the receiver is tucked inside the heart casing, the signal may be weakened.


selectedImg


Replace the old USB receiver with the one included with the new keyboard remote. Make sure the USB cable hangs properly below the heart module to ensure good signal range (see the image above). Once connected, the new keyboard remote should start working within a few seconds, as long as the battery is fully charged. If the orange light on the remote is flashing, refer to the 'Re-synchronization' section at the end of this article.

Möbil

Under the main module of your mobile unit, you should see the USB receiver for the keyboard remote. Depending on your unit model, the receiver may be located in one of two places. Disconnect the old receiver and plug in the one provided with the new remote. The remote should begin working within a few seconds if the battery is fully charged. If the orange light on the remote flashes, refer to the 'Re-synchronization' section below.


selectedImg

Or

selectedImg

Notes

Some Möbil units include a USB extension cable under the main module to improve signal reception. We recommend not removing this cable.

Lü 1st generation

Using a ladder, lift, or scaffold, access the sound and light module. The receiver is visible beneath the light module, so there's no need to open it. Through the mesh or openings of one of the lights, you should see the USB receiver connected to an extension cable. Unplug the old receiver from the end of the cable and connect the one provided with the new keyboard remote. The new remote should start working within a few seconds if the battery is fully charged. If the orange light flashes, refer to the 'Re-synchronization' section below.

selectedImg

selectedImg

Warning

Re-synchronization Instructions


If your keyboard remote doesn’t connect automatically, follow these steps:

  1. Unplug the USB receiver from the computer (you can skip this step and step 5 if the receiver is not accessible).

  2. Turn off the keyboard remote.

  3. Press and hold the F1 key on the remote.

  4. Turn the remote back on, then immediately release the F1 key.

    The third LED should start flashing quickly in orange.

  5. Reconnect the USB receiver to the computer.

    The orange LED should stop flashing, and only the blue LED should remain on.


Still have questions? Contact us!        


      • Related Articles

      • Troubleshoot for Lü keyboard-remote

        1. Make sure the keyboard-remote is fully charged. 2. Ensure that it is set to “ON” and that a blue light is illuminated. If a blue light is flashing, the keyboard-remote’s battery is running low and needs to be charged. The red light will turn off ...

      • Fixing remote pairing: Flashing orange light

        An orange flashing light on the keyboard remote, even when no keys are being pressed, indicates that it is no longer paired with its USB receiver. To re-synchronize the keyboard remote, follow these steps: 1. Turn off the remote. 2. Press and hold ...

      • Best Practices

        1. Starting Lü: Turn on the projector and the remote keyboard remote. Wake up your Lü by pressing any key on the keyboard remote to start using it. 2. Troubleshooting: If something is wrong with the system, restart the computer first. In the Lü ...

      • Lü is not responding or LU.exe has stopped working

        If a window appears with a message stating that the Lü application has stopped working, please follow these steps: 1. Close the message window. 2. Restart the Lü application. 3. If necessary, restart the computer. Still have questions? Contact us!

      • My Lü app is not working properly

        If your Lü system is behaving differently than usual, the first troubleshooting step you can try is to restart the computer. This should reset the Lü software and potentially resolve the issue. Should the problem persist, please don't hesitate to ...